Goodman / Soderberg Fatigue Diagram

Inspectable records

Ledger state

The current ledger marks this instrument verified clean within the source-bound verification corpus.

Area

Mechanical, Civil & Structural Engineering — Statics/Dynamics, Strength of Materials, Machine Design, Civil, HVAC, Vibration

Tranche

tranche-6

Evidence ID

t6-064

Ledger rows

1

No ledger note is attached.

Review findings

The Goodman and Soderberg core formulas are correct under the stated assumptions. The instrument should remain labeled as an educational fatigue estimate, not a certified design tool, as already specified. Verdict is NEEDS_REVIEW because the Gerber safety-factor definition, compressive-mean-stress policy, and plotting conventions are not fully specified.

Formula and scope findings

• The Goodman and Soderberg relations are standard failure-line equations when sigma_a is alternating-stress amplitude, sigma_m is tensile mean stress, and all stresses use consistent units. The safety factor is correctly obtained as SF = 1/(sigma_a/Se + sigma_m/Su) for Goodman or SF = 1/(sigma_a/Se + sigma_m/Sy) for Soderberg under proportional loading.
• The Gerber alternative is underspecified. A common failure locus is sigma_a/Se + (sigma_m/Su)^2 = 1, but the corresponding proportional-loading safety factor requires solving sigma_a/(SF*Se) + (sigma_m/(SF*Su))^2 = 1; this should be stated explicitly.
• The implementation must define treatment of compressive mean stress. Simply substituting a negative sigma_m into the linear Goodman or Soderberg equation can predict an unrealistically unlimited or overly favorable benefit; a mean-stress correction policy is required.
• The plot specification does not define axis conventions, allowable domain, or whether the displayed line is the failure locus at SF = 1 or a design line at a selected safety factor.

Unit assumptions

• sigma_a, sigma_m, Se, Su, and Sy must all be stresses in the same units before calculating ratios; MPa and ksi must not be mixed without conversion.
• sigma_a is assumed to be a nonnegative stress amplitude and sigma_m is assumed to be the signed mean normal stress, normally tensile for these diagrams.
• Se is assumed to be the corrected endurance limit for the specified material, surface, size, reliability, loading mode, and environment; it is not automatically the uncorrected laboratory endurance limit.
• For these vectors, 1 ksi = 6.895 MPa is used where conversion is shown.
• The plotted Goodman failure line is sigma_a = Se*(1 - sigma_m/Su), the Soderberg line is sigma_a = Se*(1 - sigma_m/Sy), and the Gerber curve is sigma_a = Se*(1 - (sigma_m/Su)^2), each over the tensile domain 0 <= sigma_m <= the applicable intercept.

Boundary hardening

BREAK_CLAIMED · SELF_FLAGGED

The zero-stress input makes the direct safety-factor calculation divide by zero, and the convention probe shows that interpreting compressive mean stress as signed versus as a magnitude changes the result from 4 to 4/3.

Errata and corrections

No applied erratum is attached to this unique-name record.

Inspectable example

4 review vectors are recorded. One source-bound sample is shown below.

{
  "inputs": {
    "method": "Goodman",
    "sigma_a": 120,
    "sigma_m": 80,
    "Se": 240,
    "Su": 600,
    "units": "MPa"
  },
  "expected_outputs": {
    "safety_factor": 1.578947368,
    "operating_point": {
      "sigma_m": 80,
      "sigma_a": 120,
      "units": "MPa"
    },
    "sampled_failure_line_points": [
      {
        "sigma_m": 0,
        "sigma_a": 240
      },
      {
        "sigma_m": 80,
        "sigma_a": 208
      },
      {
        "sigma_m": 600,
        "sigma_a": 0
      }
    ],
    "key_curve_features": {
      "sigma_a_intercept": 240,
      "sigma_m_intercept": 600,
      "roots": [
        {
          "sigma_m": 600,
          "sigma_a": 0
        }
      ],
      "extrema": [],
      "asymptotes": []
    }
  },
  "working": "Goodman denominator = sigma_a/Se + sigma_m/Su = 120/240 + 80/600 = 0.5 + 0.133333333333 = 0.633333333333. Therefore SF = 1/0.633333333333 = 1.578947368. Failure-line samples: at sigma_m = 0, sigma_a = 240*(1 - 0/600) = 240 MPa; at sigma_m = 80, sigma_a = 240*(1 - 80/600) = 240*(0.866666666667) = 208 MPa; at sigma_m = 600, sigma_a = 240*(1 - 1) = 0 MPa."
}

Related workflows

No source-defined multi-instrument workflow membership is recorded.

Sources and evidence

These pointers bind the page to evidence. They do not grant authority or collapse verification into deployment.

• VERIFIED_LEDGER.json · VERIFIED_CLEAN
• evidence-tranche6/tranche6-results.json
• BOUNDARY_HAZARD_CATALOG.json